Take the guesswork out of installing cables, wires and housing inside the frame. The IR-1.2 speeds the internal frame routing of electric wires, shift cable/housing, brake cable/housing and hydraulic tubing on carbon fiber, titanium, and aluminum frames. Kit includes four plastic-coated 250cm cables with attached magnets and unique fittings plus an external guide magnet to speed operation. Newly updated to include a dedicated E-tube Di2 cable connector that easily pulls through a 6mm frame hole. Opposite polarity magnets on cables seek and attach inside frame tubes, making it easy to route through frame entrances and exits. Works with any size frame including tandems. A true time and frustration saver!
Park's Master Chain Tool is designed specifically to work with the tight tolerances and narrow profiles of 10- and 11-speed chains and all high-quality derailleur chains. It's made of tool steel for excellent durability and uses an integrated link pocket to ensure precise alignment. It also features perfectly contoured, cushioned handles for comfort and ease of use. This pro-level chain tool includes a removable anvil to peen Campagnolo 11-speed chains. (The CT-4.3 is not compatible with Wipperman chains.)
What's your seatpost size again? Park's Digital Caliper accurately measures seatposts, head tubes, bearings, spoke diameters, etc. It's a precision instrument built accurate to 0.01mm with a stainless-steel mechanisms and a rugged composite body. The tool’s ability to measure in metric, decimal inch, and fractional inch makes it an indispensable home workshop tool. It features an automatic shut-off and comes with a protective sleeve and the battery.
Park Tool's Thru Axle Adaptors make it possible to adapt all Park Tool Truing Stands to work with 12mm, 15mm, 20mm, and 25mm thru axle front wheels, as well as Cannondale Lefty wheels (each sold separately). The TS-TA also work with the rear 135mm thru axle hubs in the TS-2.2 and TS-3. The TS-TA when used in the TS-8, TS-25, TS-15, TS-7 or TS-5 will work with all rear thru axle hubs. For thru axle hubs greater than 135 (142, 150, 157, etc.) in the TS-2.2, use the TS-2TA Thru Axle Adaptors (sold separately).
Keep your most commonly used tools close at hand with this clever, multi-function tool holder. The TK-4T was painstakingly designed with pockets and holders for specific tool shapes and sizes as well as some generic storage areas. The Tool Kaddie rotates for easy access and is molded from a durable composite material. - Bench Top Mount sits firmly on any flat surface - Specific slots and holders for 3-way hexes, screwdrivers, P-Handles, pliers/cutters - Generic slots and holders to hold a wide variety of tools and small parts - Mounting location to directly attach HXH-2P or HXH-2T P-Handle Holders (sold separately) - Built-in receiver port for PTH-1 Paper Towel Holder (sold separately)
Keep your most commonly used tools close at hand with this clever, multi-function tool holder. The TK-4 was painstakingly designed with pockets and holders for specific tool shapes and sizes as well as some generic storage areas. The Tool Kaddie rotates for easy access and is molded from a durable composite material. - Stand Mount mounts to any Park Tool Professional Shop Stand (all versions of PRS-2, -3, -4, and -33) - Specific slots and holders for 3-way hexes, screwdrivers, P-Handles, pliers/cutters - Generic slots and holders to hold a wide variety of tools and small parts - Mounting location to directly attach HXH-2P or HXH-2T P-Handle Holders (sold separately) - Built-in receiver port for PTH-1 Paper Towel Holder (sold separately)
Securely holds any of Park's TS-2, TS-2.2, and TS-2.2P Professional Wheel Truing Stands and tilts 20 degrees from front to back for comfortable wheel work and sight lines at any bench height. Features a wide, sturdy base, small parts compartments, spoke wrench holders, and is constructed of a durable composite material.
Securely holds the TS-4 Professional Wheel Truing Stand and tilts 20 degrees from front to back for comfortable wheel work and sight lines at any bench height. Features a wide, sturdy base, small parts compartments, spoke wrench holders, and is constructed of a durable composite material.
Securely holds the TS-4.2 Professional Wheel Truing Stand and tilts 20 degrees from front to back for comfortable wheel work and sight lines at any bench height. Features a wide, sturdy base, small parts compartments, spoke wrench holders, and is constructed of a durable composite material.
The BDT-2 is a go/no-go style gauge designed to help set the proper tension on most belt drive systems and sizes. Also gauges rear cog parallelism and angularity.
The 1729-TA Sliding Thru Axle Adaptor is designed to allow any Park Tool PRS-20, PRS-21 or PRS-23 Repair Stand to accept 12mm and 15mm thru axle wheeled bikes.
Park's Tire Seating Tool is designed to quickly seat the bead on stubborn tires. During inflation some tire beads can slip below the rim edge and become difficult to pull out and align. The PTS-1 comes to the rescue with its non-slip jaws and vinyl-coated handles that provide plenty of leverage for pulling out the tire. Plus, it's adjustable to fit various tire widths.
Precision CNC machined dual-sided aluminum tool for the installation and removal of 12- and 16-notch external bearing bottom brackets. Anodized for easy identification and featuring a ratchet/torque wrench compatible 3/8" drive. - Fits Enduro T47: 16-notch 52.2mm OD cup - Fits Enduro PF30: 16-notch 52.2mm OD cup - Fits Chris King ThreadFit T47: 12-notch 50.4mm OD cup - Fits Chris King ThreadFit 30: 12-notch 50.4mm OD cup
Many bicycles will not shift or track properly because the front and rear wheels are not in line with the frame. If these conditions still exist after wheel and derailleur adjustments, the seat stays, chain stays, and rear drop outs of the frame may be misaligned. For years the accepted method to check the alignment of the rear drop-out was to run a string on either side. This method does work to some extent. However, it is not accurate because the measurement is not taken at the drop-out. With the Park Tool Frame Alignment Gauge, the alignment can be checked quickly and accurately at the drop-out. It includes a retractable pointer to fit all sizes and types of bicycles.
Suspension maintenance and tuning require tools designed for a precise fit. The SKT-6 from Park Tools is a shop-quality set of six flat-faced sockets designed for use with common suspension fork fittings. Ideal for use with Park Tool Torque Wrenches, the 3/8-inch drive sockets are forged from tough chrome vanadium steel and chrome plated for lasting durability. - 24, 26, 27, 28, 30, 32mm flat-faced sockets - All sockets are 3/8" drive - Note: 27mm socket is tapered for better access on Suntour suspension forks
Truing stand upright extensions install in seconds on any TS-2 or TS-2.2 Truing Stand, allowing the stand to be used on wheels with hubs up to 200mm wide (tandem, fat and downhill bikes), as well as on wheels with a 29-inch mountain bike tire installed*. In addition, specially sized bosses serve as adaptors so the stand can be used with wheels using thru-axle hubs with removable axles. Same features as the the TS-2EXT.2 with the addition of slots to secure rear drive e-bike wheels. * Note: TS-2.2 Truing Stand does not require these adaptors to accommodate 29-inch wheels but does require it to fit hub widths from 180mm to 200+mm.
Park Tool's TS-RK is a complete rebuild kit for the TS-2 truing stand. It is complete with the most commonly replaced small parts and the instructions needed to get your stand back into top working condition. In addition to making the stand more accurate and reliable, once installed, the new parts also allow the stand to be readjusted much more easily, should it be thrown out of adjustment. This is a great addition to the older TS-2 stands. If your stand has silver-colored shaft collars, upgrade with the TS-RK. The TS-RK includes the following: • 1 - #211S Main Shaft • 4 - #749-1 Bearing Washer • 2 - #748-1 Needle Bearing • 2 - #209-2 Shaft Adjusting Collar • 1 - #229 Spring • 4 - #232-2 Split Nylon Bushing • 2 - #235-2 Split Nylon Bushing • 1 - #222-SR Right Caliper Spring • 1 - #222-SL Left Caliper Spring • 1 - Set of Installation and Adjustment Instructions
A simple, one position version of our WH-1 Wheel Holder. The WH-2 is a quick and easy solution to securely hold nearly any wheel to make tire, wheel, cassettes and hub work a snap. Can be bolted or clamped to a bench or installed in a bench vise. Includes axles and adaptors to fit 12, 15 and 20mm thru axles as well as quick release and solid axle hubs.
Park's Torx Wrench Set includes T-handled T6, T8, T10, T15, T20, T25, T30 and T40 Torx wrenches with offset handles made from durable nylon in a comfortable, ergonomic design. The wrenches are made of high-torque industrial steel for exceptional durability. Plus, this set of super tools comes with a wall mount for easy access.
• Secure engagement, easy to use, and fast! • The CP-1 quickly grips cogs from 9 to 24 teeth with no manual adjustments • A great shop tool, the CP-1 is 13.7" (35cm) long and can be used with one hand to hold cassettes solidly during lock ring removal • Forged steel construction with a spring loaded return and comfortable dual density grips.
Park's Freewheel Remover Wrench provides superior leverage for freewheel removal and installation. Its head slides over Park freewheel removers and features a locking knob for a secure fit.
Clean out or restore damaged threads in crank arms with Park Tool's Pedal Taps. They're sold as a set of right and left hand threads. Made of high carbon steel, precision ground, and hardened to stay sharp, they cut easily and fit all conventional tap handles. • Includes a set of 2 taps, 9/16" x 20 tpi • Made of high carbon steel, precision ground, and hardened to stay sharp • Fits all conventional tap handles The tap drill size for a 9/16-inch x 20 tpi thread is nominally 33/64-inch.
Park Tool's 750.2 Centering Cone Adaptor increases the size of the centering cone of the HTR-1 and HTR-1B Headtube Reaming and Facing Sets. The 750.2 will allow you to use the HTR-1(B) to ream and face head tubes designed to accept IS, ZS, and 1.5-inch EC headset standards. Before reaming or facing, make sure you have the correct cutting tool and pilot for the headset standard(s) you are using. Please refer to our product pages for cutters and pilots for this detailed compatibility information.
Secure engagement, easy to use, and fast! The CP-1.2 quickly grips cogs from 9 to 24 teeth with no manual adjustments. A great shop tool, the CP-1.2 is 13.7-inches (35cm) long and can be used with one hand to hold any 5-speed to 12-speed road or mountain cassette solidly during lock ring removal. Forged steel construction with a spring loaded return and comfortable dual density grips.
Commonly referred to as a 4th Hand, Park's Cable Stretcher pulls cables tight. Its one-hand operation and thumblock holds the cable so you can easily maintain cable tension while tightening cable fixing bolts and nuts. Made from chrome-plated and heat-treated steel and featuring cushion grips for comfort, the Park Cable Stretcher is a must for any serious mechanic.
The Park Tool SBS-1.2 is a shop-quality set of sockets, hex bits, and Torx style bits, selected specifically for common bike repair needs. Ideal for use with Park Tool torque wrenches, the SBS-1.2 3/8" drive bits and sockets are made from tough, chrome vanadium steel for lasting durability.
Precision CNC machined dual-sided aluminum tool for the installation and removal of 12- and 36-notch external bearing bottom brackets. Anodized for easy identification and featuring a ratchet/torque wrench compatible 3/8-inch drive. Fits Praxis M30 and M35 - M30: 12-notch 48mm OD cup - M35: 36-notch 51.7mm OD cup
The BDT-1 solidly holds a belt drive rear sprocket (like a chain whip holds a chain drive cassette sprocket) so the nut or lockring can be removed. - Fits most major manufacturers’ sprocket sizes - Heavy duty, heat treated steel - Durable black phosphate finish - Vinyl dipped handle
In the tradition of our premium quality fold up tools, the BO-4 is a combination corkscrew and bottle opener complete with a knife/foil cutter. This multi-tool folds for storage and features all stainless steel mechanisms housed in a forged aluminum case. This is a top quality beverage tool perfect for the workbench, toolbox or wine bar.
Park Tool's Bottom Bracket Bearing Tool Set removes and installs (with a bearing press which is sold separately) BB86, BB90, BB92 and Press Fit bottom brackets from Shimano, Race Face, SRAM and others that use a nominal 24mm-diameter spindle. This tool has a bearing remover that fits inside the bottom bracket shell and into the bearing so the bearings can be tapped out of the frame with a hammer. The set also includes two bushings that you use in conjunction with a bearing press for precision bearing installation (bearing press sold separately).